| Ausrichtungsfehler | Fehler bei der Druckkopfausrichtung. |
| Lösung: Wenn das Druckbild ok ist, dann eventuell das Papier auf "Fotopapier, glanz" umstellen. |
| 0000D8 | External Library Error. |
| 5D0273 | External Library Error. |
| — Kann JetDirect-Card oder Firmware Simms oder Motherboard sein. |
| 01002D | The Main PCA Cannot Communicate With The Carriage. |
| 010020 | FirmWare DIMM Test Failure. |
| 010021 | Memory Module Test Failure. |
| 010023 | EEROM Test Failure. |
| 010028 | EEROM Checksum Failure. |
| 010029 | EEROM Write Failure. |
| 010040 | Error In Paper-Axis Encoder Quadrature. |
| 010041 | Error In Scan-Axis Encoder Quadrature. |
| 010042 | Error In Service Station-Axis Encoder Quadrature. |
| 010050 | PostScript Processing Error. |
| 01009X | Error In Paper-Axis Motor Encoder. |
| 02xxxx | PostScript/Firmware Error. |
| 04Cxxx | EIO Accessories (EIO Card/Hard Disk Drive) Error. |
| 048xxx | EIO Card Is From A Third Party Vendor May Not Be Fully Compliant With IIO Protocol Specification2.0 OR EIO Card Firmware Is Not Updated. |
| 048500 | There Are Too Many EIO Cards Connected To Printer. |
| 060300 | One Of The Printheads Has Internal Electrical Problem. |
| 060301 | One Of The Printheads Has Internal Electrical Problem. |
| 060305 | Thermal Shutdown Error (One Of The Printheads Has Gone Above Maximum Temperature). |
| 060306 | Problem With Printhead Selection. |
| 060307 | APA Regulation Failure. |
| 060308 | APA Regulation Failure. |
| 060309 | Problem With Setting The Voltage Of Printheads. |
| 06030A | Error In Finding The Mark Encoder. |
| 06030B | The Ambient Temperature Measured Is Out Of The Normal Range. |
| 070100 | Firmware Error. |
| 080001 | PostScript Error. |
| 09xxxx | EIO Accessories (EIO Card/Hard Disk Drive) Error. |
| 09Axxx | Internal Error. |
| 09A001 | There Are Too Many Hard Disk Drives Connected To The Printer. |
| 09Bxxx | Internal Error. |
| 09Cxxx | Internal Error. |
| 0A0000 | The Air Pressure Is Below The Minimum Requirement. |
| 0A0010 | Problem In Pressurizing The Air System. |
| 0A0020 | Error In Calibrating The APS Sensor. |
| 0A0030 | Problem In Depressurizing Air System. |
| 0A0040 | Ink Tubes Initialization Failure Due To Low Air Pressure. |
| 0A0050 | The Printer Has Detected A Leak In The Tubes System Before The Life Of The System. |
| 0A0060 | The Printer Has Detected A Leak In The Tubes System After The Life Of The System. |
| 0A0070 | The Backup EEROM Contents Stored In The Tubes Systems Are Not Consistent With The Ones Required By The Firmware. |
| 0B0000 | Bad Ambient Temperture Measured. |
| 0B0001 | Bad Humidity Read. |
| 0B0002 | Bad IDS Pressure Read. |
| 0B0003 | ACDO Internal Channles Check Failure. |
| 0B0004 | Unable To Detect Pump. |
| 0B0005 | Unable To Detect Valve. |
| 0B0006 | Trailing Cable Incorrectly Connected OR Fuse In Electronics Module Has Burned. |
| 0B0007 | Unable To Detect Vacuum Fan. |
| 0B0008 | Unable To Detect Cooling Fan. |
| 0B0009 | Unable To Detect Aerosol Fan (Including On Right Cover). |
| 0B000A | Primer Shut Down Error. |
| 0B000B | Pump Or Pressure Sensor Not Working. |
| 0B000C | Serial Device ADC Test Failure. |
| 0B000D | 24 V Source Test Failure. |
| 0B000E | Short Circuit In Scan-Axis Motor. |
| 0C0030 | Bad Drop Detector. |
| 0C0032 | Drop Detector Not Calibrated For All Printheads. |
| 0C1000 | Primer Not Calibrated. |
| 0C1001 | Primer Shutdown Error. |
| 0D00xx | System Error Code Related To The Multi-roll Feeder. |